Throttle Input Devices


 

We take the throttle input of the motor speed controller very seriously! This is the critical link between driver and motor that must be guaranteed to operate correctly in the EMI warzone of an electric vehicle. Our controllers require the use of a dual channel throttle units. The redundant channels ensure that the intended throttle signal is read by the controller under a variety of possible noise and failure scenarios. We offer two high-quality input units that, with the addition of the complete cable assemblies we also carry, make connection of the throttle to the controller simple and reliable. The throttle cable assemblies must be combined with the throttle units.


 

Some of our value-added authorized resellers may package the cable assembly together with the throttle eliminating the need for end-users to choose the cable assembly for the target controller.


 

Price sheet with MSRPs


 

WarP-Drive Prius-Style Hall-Effect Pedal Assembly

Installation Manual

 

 

The WarP-Drive Prius-Style Hall-effect Pedal Assembly (HEPA) is an automotive accelerator pedal assembly based on the Prius pedal with dual Hall-effect sensors. It includes dual return springs and has convenient mounting points. The Hall-effect unit eliminates the annoying wear out of regular pot boxes.

 

The pedal will require a custom bracket for mounting and may not fit all cars.

 

Part #TPS-PRS


WarP-Drive Cable-Drive Throttle Assembly

(cable sold separately)

 

Installation Manual

 

 

 

The WarP-Drive Hall-effect cable-pull throttle assembly is a patent-pending design originating here at NetGain Controls. It is is an automotive-quality throttle input device with dual Hall-effect sensors and a variety of features to make it reliable and easy to install. It includes dual return springs. It also comes with an additional spring to allow for customization of the return tension by replacing the heavier spring with a lighter one.

 

The Hall-effect unit eliminates the annoying wear out of regular pot boxes. The device easily accommodates various installations, where different throttle cable travel distances are required for each vehicle. This is accomplished with a set of 5 inner discs, giving the following travel options: 1.125", 1.25", 1.5", 1.75", and 2". The stock throttle cable is inserted between the top and bottom discs by removing the top disc, selecting the appropriate inner disc corresponding to the right travel distance, replacing the top disc and securing it, then reattaching the springs.

 

Part #WDT-CP


Throttle Cable Assemblies

 

These throttle cable assemblies are professional assembled to provide safe and reliable reception of the throttle signal from the throttle sensor. They use high quality waterproof connectors and shielded wire that includes a drain wire. The drain wire is connected at the controller end and grounded internally in the controllers.

 

  • Cables 82115 and 82116 are shipped with the pedal-end connector not installed. This allows the cable to be routed through any necessary holes (such as the firewall) during installation. Ensure that the cable is protected from wear and damage by properly securing it and using rubber grommets and insulation against sharp edges. For the cables with connectors on both end, it is strongly recommended that the cable length not be modified. Any extra cable that remains after installing can simply be curled and tucked in a discrete location as distant from power cables as possible.
  • Cables 82114 and 82118 have no controller-end connector. This enables other select controllers to be used with our high quality throttle units.
  • Cable 82119 is used with throttle devices other than those that we carry and for use with the WarP-Drive 2 controller.

 

Instructions for attaching and removing the pedal-end connector for 82115 and 82116
Instructions for installing 82119 assembly to a throttle unit

 

Note: Some of our authorized resellers may package these cable assemblies together with their corresponding throttle units.

 

Part #82114

Length: 10ft
First connector: Blank
Second connector: TPS-PRS

Part #82115

Length: 10ft
First connector: WD1
Second connector: TPS-PRS

Part #82116

Length: 10ft
First connector: WD2
Second connector: TPS-PRS


Part #82118

Length: 5ft
First connector: Blank
Second connector: WDT-CP

Part #82113

Length: 5ft
First connector: WD1
Second connector: WDT-CP

Part #82117

Length: 5ft
First connector: WD2
Second connector: WDT-CP


   

Part #82119

Length: 10ft
First connector: WD2
Second connector: Blank

 

 

 

 

To request further information you may contact us, or one of our Authorized Resellers.

You may also contact us via the following:
NetGain Controls, Inc.
255 N 950 W, STE A7
Logan, Utah 84321

E-mail: sales@ngcontrols.com

(Priority is being given to e-mail at this time. If you purchased from a dealer, contact them before attempting to contact the factory)

 

Problems with these web pages?  Contact the person responsible for the problems!
Website Terms of Use